---
title: Pezag Eco Duo
slug: help-center/pezag-eco-duo
docTags: 
createdAt: 2025-03-14T11:13:35.327Z
---



1\. **Access to the web interface :**

1. Make sure your device is connected to the local network.   
2. Use software such as Advanced IP Scanner to find the IP address of the device.   
3. Open a web browser and enter the IP address of the device in the address bar.    
4. Log in with the default credentials :

**Username** : manufacturer

**Password** : manufacturer

![](https://api.archbee.com/api/optimize/N5BtsfQVOxPnQzfUQkalm/fp9z9njKhoRYIXNnyc76C_webinterface1.png)

![](https://api.archbee.com/api/optimize/N5BtsfQVOxPnQzfUQkalm/qIPCw0qWww5WrZcG0OiIJ_webinterface2.png)

![](https://api.archbee.com/api/optimize/N5BtsfQVOxPnQzfUQkalm/PFp6jIlJiFuUmYg1sWDVB_webinterface3.png)

###



### 2. Network configuration :   

- Navigate to the network.    
- Under the **Ethernet **tab, activate the **Automatic Assignment (DHCP)** option. This allows the device to automatically obtain an IP address from the network.



![](https://api.archbee.com/api/optimize/N5BtsfQVOxPnQzfUQkalm/4G5auVarIQFkQDbQCKb03_webinterface7.png)

###

### 3. Configuration Modbus :

- Go to the Modbus section.   
- Set the Modbus start register to -1, which is the default setting.

![](https://api.archbee.com/api/optimize/N5BtsfQVOxPnQzfUQkalm/EOEFxNF9vk4zqBhT1NxGj_webinterface4.png)

###

### 4. Configuring the charge points: 

-  For each charge point, proceed as follows:      

**1. Define the name and location of the charge point:**    

- Go to the Charge point configuration tab.  
- Enter the desired name and location.

**2. Set Locking Mode :       ** 

- Set **Locking Mode** to **On EV connected disconnected**. This ensures that the charge point will be locked or unlocked depending on the connection status of the electric vehicle.

**3. Define the charging current parameters : **       

- Set the following parameters for the charging current:    
  - Minimum charge current: set to 6A (or your preferred value).    
  - Maximum charge current: set to 22A (or your preferred value).   
  - **Fallback charge current**: set to 6A (or your preferred value)..         

**4. set the meter type : **       

- Select the correct meter type installed in your device. For example:  
  - Phoenix Contact EEM-EM357 
  - Phoenix Contact EMM-DM357 - 

*You can find this option in the Meter Type section. select the current meter type fitted in the device (e.g. Phoenix Contact EEM-EM357 / EMM-DM357).*


-

![](https://api.archbee.com/api/optimize/N5BtsfQVOxPnQzfUQkalm/3QBYoUwzZhz2VHUqyTQUS_webinterface9.png)

![](https://api.archbee.com/api/optimize/N5BtsfQVOxPnQzfUQkalm/KbYKmACG-jyBPxZz-mijT_webinterface5.png)

![](https://api.archbee.com/api/optimize/N5BtsfQVOxPnQzfUQkalm/tAfZ47N6Moy678RCb6b58_webinterface8.png)

###

###

**5. Save the configuration :**

- Once all the settings have been made, be sure to save the configuration for each charge point.    
- The settings can be exported and used and adapted on another chargepoint.

![](https://api.archbee.com/api/optimize/N5BtsfQVOxPnQzfUQkalm/dEEQpo3kJgUHWYrsECsTC_webinterface10.png)